Can a boat transom be repaired?

10
Cecilia Walker asked a question: Can a boat transom be repaired?
Asked By: Cecilia Walker
Date created: Sat, May 29, 2021 4:36 AM
Date updated: Wed, Jun 29, 2022 7:38 AM

Content

Top best answers to the question «Can a boat transom be repaired»

Long term, the plywood in the transom looses strength and becomes very flexible, allowing the gelcoat and fiberglass to crack. While it is a pretty complicated job, replacing the transom core isn't impossible. Transoms are usually replaced from inside the boat.

FAQ

Those who are looking for an answer to the question «Can a boat transom be repaired?» often ask the following questions:

⚓ Can a fiberglass transom be repaired on a sailboat?

  • Because skin repair requires a 12-to-1 scarf angle, the repair area can extend several inches beyond the edges of the transom. On a powerboat, this normally requires some repair and refinishing of the exterior skin beyond the transom corners, onto the sides and bottom of the boat.

⚓ Can a rotted transom be repaired on a boat?

  • For more serious cases, it’s possible that you may need to get the opinion of an expert, who might have to disassemble the transom. But, if you can repair and strengthen the wood with dry rot in its early stages, you can do a lot to maintain the quality of your boat.

⚓ Can a torn boat seat be repaired?

  • Torn boat seat upholstery can cause extreme damage to the seat itself if it's not fixed. It's much more affordable to repair a tear than it is to replace the entire seat. Since most marine upholstery is made of vinyl, the repair is simple.

⚓ Can a transom be repaired on a boat?

  • Repairing the transom is not that difficult if you have the right tools and equipment. Below is a detailed guideline on how to repair the transom on your boat. To make any repairs to your boat or transom, you first need to get your boat out of the water and into a dry dock or a raised platform. This is to give you more access to the transom.

⚓ Can a transom be repaired on an aluminum boat?

  • Thankfully, repairing/replacing a transom is a pretty simple job on an aluminum boat (aka "tin boat"). You'll need to start by removing all of the hardware holding the old transom in place. Don't be surprised if you have to hack, chop, scrape and drill the old bolts and rivets out.

⚓ Can the transom of a boat be repaired?

  • To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience. Repairing the transom of the boat is a minor boat repair since the transom is the flat area located at the back of the boat.

⚓ Can you repair boat transom yourself?

To make any repairs to your boat or transom, you first need to get your boat out of the water and into a dry dock or a raised platform. This is to give you more access to the transom. Allow the transom to dry completely before you can start repairs. Continue reading below Our Video of the Day

⚓ Can you repair boat transom?

While it is a pretty complicated job, replacing the transom core isn't impossible. Transoms are usually replaced from inside the boat. This means removing all the internal structure, seats, and tanks, etc. so you can work on the transom.

⚓ How much to repair boat transom?

The cost to replace the transom on a boat will vary greatly depending on whether you pay someone to do it, or if you do it yourself. After some research I came across prices as high as $5,000 to have it done professionally, but I'll show you how I was able to do it myself for about $263.

9 other answers

Repairing the transom of the boat is a minor boat repair since the transom is the flat area located at the back of the boat. Repairing the transom is not that difficult if you have the right tools and equipment. Below is a detailed guideline on how to repair the transom on your boat. Step 1 - Dry the Boat

Repairing A Rotted Transom Once you’ve looked for water trapped in the transom and other issues that could have caused the rotting, it’s time to think about the wood itself. If you caught it early enough, it might be possible that you can avoid expensive repairs. One method is to use a product like Git-Rot from BoatLIFE.

Once you have determined that there is damage, there are a couple approaches you can use to repair the transom. Access to the damaged core is required and is normally attained by removing the fiberglass skin from either the outside or, if possible, the inside of the transom. Which method is best depends a lot on the design of the boat.

Usually, a problem with the boat transom does mean you’re in for either a costly or a labor-intensive repair—or both. For example, repairing an outboard on your boat transom can mean removing the transom top, removing any associated fixtures, digging out bad and rotted wood, letting the interior dry, treating the area, and re-assembling.

Repairing a cracked leaking boat transom.. simple fix. Next time I would drill as deep but smaller holes. The aluminum plate was a back from an old electric...

IMPOSSIBLE Transom Repair | DIY Bass Boat Repair... I saved a ton of money and did my own transom repair.Check out Pastoral Homestead for a more comprehensiv...

Rebuilding the transom on your fiberglass boat is no easy task but unfortunately it must be done on many older boats, usually due to rot in the plywood core. In this article (and Video) I'm going to show you step by step how to remove your old rotten transom and replace it with a new one.

Most transoms have never been painted by the boat maker. that is why they rot. Replacing one is quite simple,but time consuming. You will have to remove the engines,everything that is screwed into the transom and all the bolts that hold it. Get yourself a big piece of cardboard (bigger than the transom).

For that, go with pressure treated. In fact, the APA suggests pressure treated ply in boat building. It would be my personal preference to use PT ply for the transom, stringers and decking. Others here dissagree, but the APA has done testing of resin on wet PT ply and it holds very well.

Your Answer

We've handpicked 6 related questions for you, similar to «Can a boat transom be repaired?» so you can surely find the answer!

How to repair bass boat transom?

IMPOSSIBLE Transom Repair | DIY Bass Boat Repair - YouTube. IMPOSSIBLE Transom Repair | DIY Bass Boat Repair. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't ...

How to repair boat transom video?

Replacing A Boat Transom - Part 1! If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid ...

Should a boat transom flex?

The flex/movement in the transom should not be enough to transfer stress to that part of the boat. It is not an integral support of the transom.

What is a boat transom?

The transom is the rearmost vertical structure on the boat. Most modern fibreglass boats have a transom capable of holding one or two engines, outboard or inboard motors.

Where can i get my boat repaired?
  • All Star Marine offers full service, mobile boat repair or pick up at your home or dock. With easy access through Sue Creek in the middle river area of the Chesapeake Bay, you can boat right to our marina for service. We currently maintain over 400 covered high and dry storage racks. We are located on Sue Creek, near the mouth of Middle River.
Where is a boat transom?

The cross-section of the stern, where you attach an outboard motor, is called the transom. On the top of the boat are metal fittings called cleats.