Cracked marine engine block repair cost?

12
Kelley Kessler asked a question: Cracked marine engine block repair cost?
Asked By: Kelley Kessler
Date created: Fri, Apr 23, 2021 9:08 AM
Date updated: Sun, Jul 3, 2022 2:35 PM

Content

Top best answers to the question «Cracked marine engine block repair cost»

  • You need a short block. Depending on what motor you have, figure $2500 for the block, and about the same in labor to swap it out.
  • If you do not drain the raw water from the river. It may cause winterizing the boat engine and cracked block Mercruiser. How much will cracked boat engine block repair cost? Cracked boat engine block repair will cost approximately $1,500 in parts and machining costs.

Assuming around 20 hours of labor at $100 per hour, you can expect no less than $3,500 to repair a cracked engine block.

FAQ

Those who are looking for an answer to the question «Cracked marine engine block repair cost?» often ask the following questions:

⚓ Blown head gasket repair marine engine?

Re: Blown Head Gasket Recondtioned motor was purchased by mechanic off a motor supplier and it consisted of Reco Chev 262 4.3lt V6 Mercruiser style unleaded long motor, comes with new exhausts and risers, new water pump, reco balancer, new alternator, new thermostat housing, new starter, reco carburettor, new intake manifold, new electronic distributor and leads, new flywheel, marine head ...

⚓ How much does a cracked engine block cost?

  • How much will cracked boat engine block repair cost? Cracked boat engine block repair will cost approximately $1,500 in parts and machining costs. Depending on the damage, it will take 12 to 35 hours to repair.

⚓ How much does it cost to repair a cracked boat engine block?

  • Cracked boat engine block repair will cost approximately $1,500 in parts and machining costs. Depending on the damage, it will take 12 to 35 hours to repair. If your boat engine is not performing well or it takes more time to get a start or make an odd sound. You should check if there are two or more symptoms.

⚓ How much does seloc marine engine repair cost?

  • Our database of marine engine repair offers complete service procedures, wiring diagrams, maintenence schedules, specifications, parts database, a marine dealer locator and much more. All of that for $45.99 for a 3 year subscription. Check to see if your engine is covered in SelocOnline.

⚓ How to repair marine cracked block block sealer?

How To Repair A Marine Engine With A Cracked Block - YouTube. P98723940. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't begin shortly, try restarting your device.

⚓ Is it possible to repair a cracked engine block?

  • Also, having a cracked block is one of those extreme cases where it may not be possible to salvage your current engine. There are many who have attempted to repair cracked blocks. The main difficult is that you cannot simply weld an engine block since it is made from cast iron, not steel.

⚓ Is it worth fixing a cracked engine block with k seal?

  • With a replacement block costing thousands, it’s well worth trying to fix the problem with K-Seal before going down this route. K-Seal will seal the cracks in engine blocks that cause coolant leaks, to get you back on the road and save you a small fortune.

⚓ K & j small engine and marine repair?

K&J Small Engine and Marine Repair, has been serving the Brainerd lakes area for over fifteen years with over 25 years in the Small Engine and Marine power experience. We offer a unique personalized service experience. The small home town feel of the experience is tailored to your specific needs, on every repair.

⚓ Marine engine repair company in mumbai?

D. M. SHIP REPAIRS PVT LTD. is serving the marine industry for the last many years since inception and is widely recognized in the Indian Shipping Industry as being one of the leading ship-repair company delivering quality and value to Ship Owners and Managers. The Hub of our operations is conveniently located in Navi Mumbai and we can extend support along the vast Indian coastline seamlessly.

9 other answers

Cracked Engine Block Repair Cost. Start to finish, engine block crack repair costs will set you back at least $1,500 in parts and machining costs. The labor for an engine block repair could be anywhere from 12 to 35 hours, depending on the vehicle you drive. Diesel engines and truck engines are on the expensive end of the scale while small cars and more common models are usually less time-consuming.

Re: What should it cost to replace cracked block? depends on where ya go. most shops down here in pueblo are around 100.00 an hour for the labor plus a new motor. i work on boats in my garage and i think the last 4.3 i did was around 3000.00. by the way, where in colo are you? W.

A typical engine rebuild is between $2,500 and $4,000 in parts and labor costs. This type of engine repair might include simply replacing bearings and seals, and obviously taking the engine out and re-installing it. It could be much higher too. How much does it cost to rebuild a 350 marine engine?

How To Repair A Marine Engine With A Cracked Block - YouTube. P98723940. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't begin shortly, try restarting your device.

A failure in the engine block will leave you stranded and more often than not facing a huge repair bill (at least $1,200, probably more). The cost of repairing a cracked engine block can vary considerably depending on the garage you visit, the severity of the crack and the car you drive.

The rebuilt blocks were only a couple hundred bucks cheaper. The cost was in the labor for the most part. Plus, you get into it, and you start saying, well why not replace this and that while the engine is out. I keep an engine room heater as well, but without power it doesn't work.

Cracked boat engine block repair will cost approximately $1,500 in parts and machining costs. Depending on the damage, it will take 12 to 35 hours to repair.

A cracked cylinder head or engine block may or may not be bad news depending on the size and location of the crack(s), the value of the casting and what it will take to fix the crack(s) versus what it would cost you to replace the casting. Read what your options are in this Larry Carley feature.

Welcome to the forum and sorry you had to find it by having a cracked engine block. Some can be fixed and some should not be fixed. Personally I would never feel safe in one that has been welded and although it costs a few bucks, try to find a donor block or buy and old unit and have it refurbished at an engine shop.

Your Answer

We've handpicked 6 related questions for you, similar to «Cracked marine engine block repair cost?» so you can surely find the answer!

Marine repair cost per hour?

How Much Will a Boat Mechanic Cost Me? Labor fees for marine technician service can vary by region and season, but the basic charge will be similar to the rate charged for labor at an automobile dealership, between $70 and $120 per hour.

What are the symptoms of a cracked engine block?
  • Overheating. If the crack in the engine block is severe enough and in the "right spot" it will cause antifreeze to leak from the block.
  • Engine Smoke. Blackish-gray or blue smoke coming out from under the hood is a strong indication that there is a crack in the block.
  • Antifreeze and Oil Mixing…
  • Poor Engine Performance…
What do you use to repair a cracked engine block?
  • Click here to find out. For the repair of this cracked engine block, we used Belzona 1111 (Super Metal), Belzona 9111 (Cleaner/Degreaser), Belzona 9341 (Reinforcement Tape), and a few tools from our machine shop. The engine had a few hairline spider cracks.
What happens if you have a cracked engine block?
  • A cracked engine block can result in: 1 Oil and antifreeze mixing 2 Engine overheating 3 Low engine compression 4 Excessive engine smoke 5 Visible crack in block
What to do if your boat engine block is cracked?
  • Whether you want to ensure your boat's engine block is sound after a long, hard winter or you're purchasing a used boat engine, you should check for a cracked engine block. The process can be messy, but it is straightforward in nature.
What's the best way to repair a cracked engine block?
  • To terminate the cracks, drill 3/16″ (48 mm) holes at their ends to prevent further propagation. Using Belzona 9111 (Cleaner/Degreaser) remove all residue to keep the repair area free of contaminants. Insert studs into each hole.